Skip to main content

Rock Space WiFi Extender Setup: Ultimate Guide

 Do you wish to increase the range of your current WiFi router? Have you recently purchased a new Rockspace extender and want to learn how to set it up for the first time? Are you unsure how to do Rock Space WiFi extender setup? Don't panic! You do not need to search further. In this blog, you will know the simple way to install Rockspace WiFi extender using re.rockspace.local setup.  To extend the coverage of the existing WiFi network, you just need to connect Rockspace wifi extender with your device. To know more, scroll down till the end of the blog. 

Rock Space WiFi Extender Setup



Instructions to Install Rockspace WiFi Extender


For Rock Space WiFi extender setup through the graphical user interface or WPS connection, follow the below instructions. Here are the steps to get started:

Step 1: The first step is to plug the Rockspace WiFi extender into the power socket through an electrical AC outlet.

Step 2: Connect your WiFi extender to the power AC outlet.

Step 3: After that, connect any of your WiFi-enabled devices to your extender's WiFi network. Make sure your device's mobile data is turned off.

Step 4: From your device, open any updated web browser of your choice. In the URL bar of the web address, type http://re.rockspace.local. If this web address does not work for you then try to connect Rockspace wifi extender with the default IP address 192.168.0.254.

Step 5: Next, you need to create the login username and the password for your extender. You need to choose the default username and the WiFi network that you want to extend.

Step 6: Thereafter, enter the password for the chosen wireless network. You'll have to wait until the extender start displaying on your screen.

Step 7: After you've finished the Rock Space WiFi extender setup, you can move and place it between the router and dead zones. The device's LED indicator will turn blue when the dead spots are covered.


Steps to Connect Rockspace WiFi Extender through WPS Button 

Follow the instructions below for Rock Space WiFi extender setup using the WPS button:

Step 1: To set up your rockspace wifi extender, you need to connect it to a power outlet that is closer to the router device.

Step 2: When the LED power starts blinking blue, you can begin the Rockspace wifi configuration. When the LED indicator begins to light up, press the WPS button on your router.

Step 3: After clicking the WPS button on your router, push the WPS button on the extender within 2-3 minutes. Check whether the LED light changes from red to blue or not.

Step 4: Thereafter, move your rockspace extender between the dead regions and the router. Use can see the LED indicator to evaluate the network coverage strength.

Step 5: Once the WiFi connection has reached maximum coverage strength, you can use the network without interruption.

With these instructions, you can quickly execute and complete the Rock Space WiFi extender setup without any problems. All of the steps are simple and straightforward. You can contact our technical experts if you have any problems during re.rockspace.local setup. Our professionals will assist you by offering the best advice to resolve issues to connect Rockspace wifi extender.
Labels:

Comments

Post a Comment

Popular posts from this blog

How to Do Orbi WiFi Extender Setup?

  With the advancement in technology, the need for the high-speed internet is also growing. Now, the users can’t bear any delayed network issues. We have seen that people will switch easily to other networks until they find an efficient wireless network. Getting reliable wireless signals becomes the challenge. A single router can provide a decent WiFi coverage within a certain range but leave certain areas of your home with poor or no WiFi coverage. If you are facing the slow WiFi signals issue then go ahead with the Orbi WiFi extender that not only boosts the WiFi signals but also eliminates the dead spots. In this blog, all you are going to know about the steps for O rbi wifi extender setup . So, without wasting any of your precious time, let us begin with the most important section of the blog.  Instructions for the Netgear Orbi WiFi Extender Setup Look at the below instructions one-by-one for the Netgear Orbi WiFi extender setup: Step 1: The first step is to unplug the exi...
Post a Comment
Read more

How Do I Setup the Nextbox WiFi Extender?

  In comparison to others, the  Nextbox wifi extender setup  is far too simple. The steps below will help you install it, access its login admin page, and configure its settings. So, without further doubt, let's begin the Nextbox extender setup process.   Nextbox Extender Installation Steps- The following are the steps for installing the Nextbox wifi extender in your home. Essentially, it will assist your router in reaching its signal range in every corner of your home. So, let's get this party started. To begin, you must unbox it. Find a suitable network signal location. Keep it there and connect it to the power source and the router network. Remove the power cable from its packaging box and inspect it for damage; otherwise, it may cause problems. So, make sure its cable and power socket are compatible and connect this power cable to both your power socket and your range extender. Wait until the signal LED stops blinking. When it starts blinking, make sure your exte...
Post a Comment
Read more

How to setup Netgear Nighthawk ac1900 modem router?

  The simplest answer to how to setup Netgear nighthawk ac1900 modem router is through the Nighthawk app. The Nighthawk app also allows you to manage your WiFi settings, view the devices connected to your network, and perform speed tests. Check Which products support the Netgear Nighthawk app to see if your product is supported. You can also configure your router using the web interface if you'd prefer to install it on a computer or if your product isn't supported. For more details, see How do I configure my NETGEAR router using the router web interface.   Utilizing the NETGEAR Nighthawk app, configure and install your NETGEAR router as follows: Get the Nighthawk application. Connect your modem to the router's Internet port after attaching any provided antennas. Start up your router. Await the WiFi LED to turn on. For your router's WiFi network name (SSID) and network key (password), check the label on the device. Your router's label can be found on the bottom or b...
Post a Comment
Read more