Skip to main content

TP-Link Access Point Setup Guide

 Are you looking to learn how to configure your TP-Link WiFi router in the Access Point mode? But, before you get to know that, we will explain what Access Point mode is? If you put your wireless device to an access point, it functions as a connection between wireless devices that connect with the router. It extends the wifi router's signal without acting as a separate device. Therefore, if you configure your WiFi extender to the AP mode (or access point mode), it means enabling it to extend the wifi router's signals in a router-only. TP-Link access point setup is described in this blog in detail, so follow the steps properly.



Steps To Perform For TP-Link Access Point Setup - 

Read the following steps to enable the TP-Link into access point mode, however, before that, attaching the TP-Link WiFi router and your current wifi router by using an Ethernet wire is suggested. Don't connect it through wifi because the configuration can be very complicated.

  1. Begin by connecting your TP-Link wifi router to your main wifi router using the help of an Ethernet cable.

  2. Switch to the TP-Link wireless router, and allow it to be able to communicate with the wifi router that is already in use.

  3. If you see that the TP-Link becomes green, it signifies that the connection has been in place and is in the process of being configured.

  4. Use an Ethernet cord to connect directly the TP-Link router to your PC device.

  5. After that, open an internet browser and type in the IP address recorded on the sticker located on the router.

  6. This IP can be found at 192.168.1.1 or 192.168.0.1 generally. When you press enter, you should see the TP-Link screen appear on your screen.

  7. Then, enter the username and password for the router that is 'admin' for password and username.

  8. Then, select the option for network and LAN.

  9. After that, configure the TP-Link router to a specific address within the network of your own home.

  10. After saving the updated settings, you will be taken away from the main screen.

You must assign an IP. You must configure your TP-Link router to be outside of the DHCP range of 192.168.1.10 to 192.168.1.100 If your primary wifi router is located within this area. You can, for instance, add 192.168.1.210 to your router from TP-Link. This will ensure there will be no IP address conflict between routers even when they are communicating.

  1. Begin by logging back into your TP-Link wifi router by entering the latest IP address.

  2. Select Wireless and settings for wireless from the menu.

  3. Keep an SSID that is distinct from the wifi routers you've set up before.

  4. Now, you can enable WPA2 as wireless security.

  5. Then, you can set a secure wifi password to ensure wireless security.

  6. Open the DHCP then DHCP settings. You can disable it by pressing on the toggle.

  7. There is a need for the use of only 1 DHCP server to be used per.

  8. Your primary WiFi router is designed to do this task.

  9. Then, select save. Next, select to restart the system by clicking the System Tools.

  10. Then, allow you to allow the TP-Link wireless router reboot and then wait for about a minute for it to load the settings for configuration.

  11. After that, disconnect the Ethernet cable from both the TP-Link wireless router and the computer and connect it using wifi.

  12. Use it to connect via the internet using your SSID as well as the passcode to join your WiFi router.

 

TP-Link Access Point Setup Complete!

After that, you've completed the TP-Link access point setup. It is important to follow these steps precisely and cautiously to switch on the access point mode TP-Link. These steps can be quite complicated for someone who doesn't have any notion of the technology and IP addresses. If you're stuck and require assistance, talk to us to receive the most effective assistance in the shortest amount of time.
Labels:
Location: United States

Comments

Post a Comment

Popular posts from this blog

How to Do Orbi WiFi Extender Setup?

  With the advancement in technology, the need for the high-speed internet is also growing. Now, the users can’t bear any delayed network issues. We have seen that people will switch easily to other networks until they find an efficient wireless network. Getting reliable wireless signals becomes the challenge. A single router can provide a decent WiFi coverage within a certain range but leave certain areas of your home with poor or no WiFi coverage. If you are facing the slow WiFi signals issue then go ahead with the Orbi WiFi extender that not only boosts the WiFi signals but also eliminates the dead spots. In this blog, all you are going to know about the steps for O rbi wifi extender setup . So, without wasting any of your precious time, let us begin with the most important section of the blog.  Instructions for the Netgear Orbi WiFi Extender Setup Look at the below instructions one-by-one for the Netgear Orbi WiFi extender setup: Step 1: The first step is to unplug the exi...
Post a Comment
Read more

How Do I Setup the Nextbox WiFi Extender?

  In comparison to others, the  Nextbox wifi extender setup  is far too simple. The steps below will help you install it, access its login admin page, and configure its settings. So, without further doubt, let's begin the Nextbox extender setup process.   Nextbox Extender Installation Steps- The following are the steps for installing the Nextbox wifi extender in your home. Essentially, it will assist your router in reaching its signal range in every corner of your home. So, let's get this party started. To begin, you must unbox it. Find a suitable network signal location. Keep it there and connect it to the power source and the router network. Remove the power cable from its packaging box and inspect it for damage; otherwise, it may cause problems. So, make sure its cable and power socket are compatible and connect this power cable to both your power socket and your range extender. Wait until the signal LED stops blinking. When it starts blinking, make sure your exte...
Post a Comment
Read more

How to setup Netgear Nighthawk ac1900 modem router?

  The simplest answer to how to setup Netgear nighthawk ac1900 modem router is through the Nighthawk app. The Nighthawk app also allows you to manage your WiFi settings, view the devices connected to your network, and perform speed tests. Check Which products support the Netgear Nighthawk app to see if your product is supported. You can also configure your router using the web interface if you'd prefer to install it on a computer or if your product isn't supported. For more details, see How do I configure my NETGEAR router using the router web interface.   Utilizing the NETGEAR Nighthawk app, configure and install your NETGEAR router as follows: Get the Nighthawk application. Connect your modem to the router's Internet port after attaching any provided antennas. Start up your router. Await the WiFi LED to turn on. For your router's WiFi network name (SSID) and network key (password), check the label on the device. Your router's label can be found on the bottom or b...
Post a Comment
Read more