Skip to main content

Steps For Victure Wifi Extender Setup

 Victure wifi extender is gaining quite some importance recently. This is because it offers amazing features to its clients. To connect the Victure wifi extender and use it, you need to perform the Victure wifi extender setup. The extender will spread the internet signals around the house and rule out the network dead spots so that you can enjoy the internet in any region of the house. For setting up your Victure wifi extender you can follow two different methods;



  1. WPS Method

  2. Internet Browser


Guidelines For Victure Wifi Extender Setup Using The WPS Method - 


If your wifi router and extender both have the wifi-protected setup then this part is for you. It is the easiest way to set up the Victure wifi extender;


  1. Plug your Victure wifi range extender as close to the wifi router as possible.

  2. Power on the extender and wait for the power LED bulb to turn up in blue color.

  3. See that the antennas of the extender are in the upward and vertical direction to the ground surface.

  4. Hit the WPS button on your wifi router device.

  5. After that, wait for at least a few minutes.

  6. Hit the WPS button on your Victure wifi range extender, next.

  7. Check if the signal LED bulb on the Victure wifi range extender becomes solid blue.

  8. After that, move the extender device and connect your wifi-compatible devices to it.

  9. Ensure the extender is plugged into an electrical socket that is centrally located in the router network and dead zones.

  10. Again wait for the signal LED bulb to turn solid blue.


Guidelines For Victure Wifi Extender Setup Using Internet Browser Method - 


In case, your wifi router network and extender don’t have the WPS push button, then this section is yours. Here we will guide you on how you can set up your wifi extender using a web browser;


  1. Insert the Victure wifi extender in the wall socket in the same area as the wifi router for a better connection.

  2. Press the power button to switch on the device. 

  3. Check if the power LED bulb becomes solid blue.

  4. Now, link your wifi-compatible device to the Victure extender’s network.

  5. Look for the SSID ‘rockspace_EXT’ in the wifi devices list.

  6. Ensure that you have switched off the mobile data.

  7. Now, on your device open the preferred web browser.

  8. Here, type the web address http://wireless.repeater in the web address field.

  9. Now, choose the wifi router network you wish to extend.

  10. Enter the wifi network’s password and then wait for the ‘Extended Successfully’ prompt to display.

  11. Move your wifi extender to a new area and then wait for the devices to establish a connection.



Victure Setup Concluded!


Victure Wifi extender setup is not a hard nut to crack. You can easily perform the setup process by following the above-mentioned methods. The WPS setup process is the easiest method of Victure extender setup. But, if your wifi router does not support the WPS button then, you can follow the browser method. Enjoy the great internet.




Labels:
Location: United States

Comments

Post a Comment

Popular posts from this blog

How to Do Orbi WiFi Extender Setup?

  With the advancement in technology, the need for the high-speed internet is also growing. Now, the users can’t bear any delayed network issues. We have seen that people will switch easily to other networks until they find an efficient wireless network. Getting reliable wireless signals becomes the challenge. A single router can provide a decent WiFi coverage within a certain range but leave certain areas of your home with poor or no WiFi coverage. If you are facing the slow WiFi signals issue then go ahead with the Orbi WiFi extender that not only boosts the WiFi signals but also eliminates the dead spots. In this blog, all you are going to know about the steps for O rbi wifi extender setup . So, without wasting any of your precious time, let us begin with the most important section of the blog.  Instructions for the Netgear Orbi WiFi Extender Setup Look at the below instructions one-by-one for the Netgear Orbi WiFi extender setup: Step 1: The first step is to unplug the exi...
Post a Comment
Read more

How Do I Setup the Nextbox WiFi Extender?

  In comparison to others, the  Nextbox wifi extender setup  is far too simple. The steps below will help you install it, access its login admin page, and configure its settings. So, without further doubt, let's begin the Nextbox extender setup process.   Nextbox Extender Installation Steps- The following are the steps for installing the Nextbox wifi extender in your home. Essentially, it will assist your router in reaching its signal range in every corner of your home. So, let's get this party started. To begin, you must unbox it. Find a suitable network signal location. Keep it there and connect it to the power source and the router network. Remove the power cable from its packaging box and inspect it for damage; otherwise, it may cause problems. So, make sure its cable and power socket are compatible and connect this power cable to both your power socket and your range extender. Wait until the signal LED stops blinking. When it starts blinking, make sure your exte...
Post a Comment
Read more

How to setup Netgear Nighthawk ac1900 modem router?

  The simplest answer to how to setup Netgear nighthawk ac1900 modem router is through the Nighthawk app. The Nighthawk app also allows you to manage your WiFi settings, view the devices connected to your network, and perform speed tests. Check Which products support the Netgear Nighthawk app to see if your product is supported. You can also configure your router using the web interface if you'd prefer to install it on a computer or if your product isn't supported. For more details, see How do I configure my NETGEAR router using the router web interface.   Utilizing the NETGEAR Nighthawk app, configure and install your NETGEAR router as follows: Get the Nighthawk application. Connect your modem to the router's Internet port after attaching any provided antennas. Start up your router. Await the WiFi LED to turn on. For your router's WiFi network name (SSID) and network key (password), check the label on the device. Your router's label can be found on the bottom or b...
Post a Comment
Read more