Skip to main content

Know How to Perform TP-Link Extender Reset

 TP-Link WiFi range extender is a fantastic device through which you can boost the WiFi signals and resolve the issues associated with it. Basically, it is a small wall socket that you can easily fix at your home and office. The process to set up the TP-Link extender at the initial time is simpler with the mobile device. However, there may be the possibility that you may face issues with the TP-Link range extender, such as disconnected web, slow internet speed, and many more, which you can resolve through TP-Link extender reset. There are various methods through which you can reset the TP-Link range extender, including soft reset and hard reset. For the soft reset of the Extender, you have to access the online interface setting page. In this blog, we have shared the instructions for both methods to reset the TP-Link range extender. Let’s get started without any delay. 


Steps for TP-Link Extender Reset from Software

Go through the below-mentioned instructions for the factory reset of the TP-Link WiFi range extender from the software:

Step 1: The first step is to plug in your TP-Link extender in the power socket. Connect your device to the extender using the WiFi connection.

Step 2: After that, log in to your TP-Link range extender device using the IP address you have configured during the first-time setup of your device. You can also use the default IP address 192.168.0.254 to log in. 

Step 3: Thereafter, go to the settings and then tap on the system tools.

Step 4: Next, tap on the backup and restore option from the menu's left pane.

Step 5: Choose the factory restore option to perform the factory reset of the TP-Link WiFi range extender. 

Step 6: A pop-up message will be displayed on the screen saying, “Do you want to perform factory default settings”? Tap on the Yes button to proceed further. 

Step 7: The TP-Link extender starts rebooting with the factory default settings and a new name for the WiFi.

Step 8: Make sure to check the WiFi signals to confirm the WiFi booster device factory reset has been done successfully. 


Steps to Hard Reset TP-Link Range Extender 

Most of the time, the hard reset is done when the user forgets the login credentials details of the extender after the setup process, such as username, password, IP address, etc. Here are the steps for the hard reset of the TP-Link range extender:

Step 1: Firstly, plug the TP-Link extender into the electrical socket and wait for some time until it turns on completely.

Step 2: Take a paper pin or needle or any sharp object to press the reset button on the TP-Link range extender. It is located at the backside of the extender.

Step 3: Press the reset button for 1 second and see if your extender will start rebooting.

Step 4: Wait for some time until the rebooting is completed. Ensure that the wireless signals display the default SSID name. 


We hope that the above steps will help you soft reset and hard reset the TP-Link WiFi range extender successfully. Thereafter, set up your range extender device again to boost and extend the WiFi signals to the long-distance even in the dead zones. Remember that the TP-Link extender reset will delete the customized settings made by you.
Labels:
Location: United States

Comments

Post a Comment

Popular posts from this blog

How to Do Orbi WiFi Extender Setup?

  With the advancement in technology, the need for the high-speed internet is also growing. Now, the users can’t bear any delayed network issues. We have seen that people will switch easily to other networks until they find an efficient wireless network. Getting reliable wireless signals becomes the challenge. A single router can provide a decent WiFi coverage within a certain range but leave certain areas of your home with poor or no WiFi coverage. If you are facing the slow WiFi signals issue then go ahead with the Orbi WiFi extender that not only boosts the WiFi signals but also eliminates the dead spots. In this blog, all you are going to know about the steps for O rbi wifi extender setup . So, without wasting any of your precious time, let us begin with the most important section of the blog.  Instructions for the Netgear Orbi WiFi Extender Setup Look at the below instructions one-by-one for the Netgear Orbi WiFi extender setup: Step 1: The first step is to unplug the exi...
Post a Comment
Read more

How Do I Setup the Nextbox WiFi Extender?

  In comparison to others, the  Nextbox wifi extender setup  is far too simple. The steps below will help you install it, access its login admin page, and configure its settings. So, without further doubt, let's begin the Nextbox extender setup process.   Nextbox Extender Installation Steps- The following are the steps for installing the Nextbox wifi extender in your home. Essentially, it will assist your router in reaching its signal range in every corner of your home. So, let's get this party started. To begin, you must unbox it. Find a suitable network signal location. Keep it there and connect it to the power source and the router network. Remove the power cable from its packaging box and inspect it for damage; otherwise, it may cause problems. So, make sure its cable and power socket are compatible and connect this power cable to both your power socket and your range extender. Wait until the signal LED stops blinking. When it starts blinking, make sure your exte...
Post a Comment
Read more

How to setup Netgear Nighthawk ac1900 modem router?

  The simplest answer to how to setup Netgear nighthawk ac1900 modem router is through the Nighthawk app. The Nighthawk app also allows you to manage your WiFi settings, view the devices connected to your network, and perform speed tests. Check Which products support the Netgear Nighthawk app to see if your product is supported. You can also configure your router using the web interface if you'd prefer to install it on a computer or if your product isn't supported. For more details, see How do I configure my NETGEAR router using the router web interface.   Utilizing the NETGEAR Nighthawk app, configure and install your NETGEAR router as follows: Get the Nighthawk application. Connect your modem to the router's Internet port after attaching any provided antennas. Start up your router. Await the WiFi LED to turn on. For your router's WiFi network name (SSID) and network key (password), check the label on the device. Your router's label can be found on the bottom or b...
Post a Comment
Read more