Skip to main content

How Do I Perform Galaway WiFi Extender Setup?

 Nowadays, almost in every home, people have a wireless network. It becomes so much important to have a WiFi signal. No one can imagine their life without an internet connection. People's lives revolve around the gadgets that require them to connect to the internet. Everyone needs such a wireless network that they can access at any place in their home or office, which can only be fulfilled with the WiFi extender. If you are also looking for such a device that not only boosts the wireless signals but also extends the signals to the area in which router signals are not able to reach. One of the biggest problems that people face with the Galaway WiFi extender is in its setup. This blog explained the guidelines for the Galaway WiFi Extender Setup. Check out the steps by scrolling down till the end.



Steps for Galaway WiFi Extender Setup Using WPS Button 

Walkthrough the below steps for the Galaway WiFi extender setup without using any wire or password:

Step 1: The first step is to locate the WPS button on your router. You will find the WPS button on the rear side of the wireless router.

Step 2: After that, long-press the WPS button of the wireless router.

Step 3: Thereafter, take the Galaway WiFi Extender, press the WPS button for 30-40 seconds, and wait until the Galaway WiFi range extender gets paired with the wireless router.

Step 4: Now, the Galaway WiFi range extender light will turn on. 

Step 5: Next, you have to check the SSID of the Galaway Range Extender displayed on the WiFi router.

Step 6: At last, connect your Galaway WiFi range extender by using the Service Set Identifier. Check whether the internet connection is working or not. 


Instructions for the Galaway WiFi Extender Setup with Personal Computer 

Another method to set up the Galaway WiFi Extender Setup and pair it with the wireless router is through the default SSID and password. Here are the steps for it:

Step 1: Galway WiFi signal booster acts as the access point with which the user will get one local area network and one wireless access network in their device. 

Step 2: After that, connect your device with the computer either through the wire or by using the default SSID Galaway to connect through the WiFi option.

Step 3: Next, open the home page of the web browser you are using. Thereafter, enter the IP address 192.168.10.1 or the web address http://ap.setup to log in to the Galaway WiFi Range Extender.

Step 4: Once you reach the setup wizard, enter “admin” as the default password.

Step 5: Now, you will see that the setup wizard will start scanning. The list of all the available wireless networks is displayed on the screen. 

Step 6: Choose your wireless network from the displayed list. Enter the wireless password for the chosen wireless network.

Step 7: Tap on the Next button to go ahead. You have to name the Galaway extender.

Step 8: Save the settings you make and then reboot your extender. 


We hope that by following the above instructions, you can complete the Galaway WiFi Extender Setup on your device. In case of any doubt, you can reach our experts through our helpline number. 
Labels:
Location: United States

Comments

Post a Comment

Popular posts from this blog

How to Do Orbi WiFi Extender Setup?

  With the advancement in technology, the need for the high-speed internet is also growing. Now, the users can’t bear any delayed network issues. We have seen that people will switch easily to other networks until they find an efficient wireless network. Getting reliable wireless signals becomes the challenge. A single router can provide a decent WiFi coverage within a certain range but leave certain areas of your home with poor or no WiFi coverage. If you are facing the slow WiFi signals issue then go ahead with the Orbi WiFi extender that not only boosts the WiFi signals but also eliminates the dead spots. In this blog, all you are going to know about the steps for O rbi wifi extender setup . So, without wasting any of your precious time, let us begin with the most important section of the blog.  Instructions for the Netgear Orbi WiFi Extender Setup Look at the below instructions one-by-one for the Netgear Orbi WiFi extender setup: Step 1: The first step is to unplug the exi...
Post a Comment
Read more

How Do I Setup the Nextbox WiFi Extender?

  In comparison to others, the  Nextbox wifi extender setup  is far too simple. The steps below will help you install it, access its login admin page, and configure its settings. So, without further doubt, let's begin the Nextbox extender setup process.   Nextbox Extender Installation Steps- The following are the steps for installing the Nextbox wifi extender in your home. Essentially, it will assist your router in reaching its signal range in every corner of your home. So, let's get this party started. To begin, you must unbox it. Find a suitable network signal location. Keep it there and connect it to the power source and the router network. Remove the power cable from its packaging box and inspect it for damage; otherwise, it may cause problems. So, make sure its cable and power socket are compatible and connect this power cable to both your power socket and your range extender. Wait until the signal LED stops blinking. When it starts blinking, make sure your exte...
Post a Comment
Read more

How to setup Netgear Nighthawk ac1900 modem router?

  The simplest answer to how to setup Netgear nighthawk ac1900 modem router is through the Nighthawk app. The Nighthawk app also allows you to manage your WiFi settings, view the devices connected to your network, and perform speed tests. Check Which products support the Netgear Nighthawk app to see if your product is supported. You can also configure your router using the web interface if you'd prefer to install it on a computer or if your product isn't supported. For more details, see How do I configure my NETGEAR router using the router web interface.   Utilizing the NETGEAR Nighthawk app, configure and install your NETGEAR router as follows: Get the Nighthawk application. Connect your modem to the router's Internet port after attaching any provided antennas. Start up your router. Await the WiFi LED to turn on. For your router's WiFi network name (SSID) and network key (password), check the label on the device. Your router's label can be found on the bottom or b...
Post a Comment
Read more