Skip to main content

How Can I Install Rockspace Wifi Extender Via re.rockspace.local?

 The Rockspace wifi extender setup is not a complicated deal. Even for newbies out there, setting up and configuring the extender is not a tough sail so, hook onto this blog, read the steps carefully, and complete the extender setup. Re.rockspace.local is the official website for extender setup, so you will learn about extender setup and configuration on this website too.


Install Rockspace Wifi Extender - 

Before setting up your extender, you need to first install it using the following steps;

  • Check the appropriate location for the Rockspace wifi extender.

  • It should be in the middle of the wifi router and network dead zones.

  • Also, it should be closer to the power outlet.

  • Now, plug the Rockspace wifi extender into that power outlet.

  • Wait patiently till the LED turns solid blue.


Methods For Rockspace Extender Setup -

Here are two distinct methods of setting up the Rockspace wifi extender - 

  1. Rockspace extender setup using re.rockspace.local - 

  • Once you have successfully connected to the wifi network, launch the web browser you use the most.

  • In the web address bar enter re.rockspace.local or you can also enter 192.168.0.254 in case re.rockspace.local doesn’t open.

  • To proceed, create a log-in password for your rockspace wifi extender.

  • This will now scan all the available networks in your area, and choose the one whose range you want to extend.

  • Then type in the password for your prime wifi, the one you have been using for your wifi router.

  • It is totally up to you to change the wifi network’s SSID. 

  • Once the setup is complete it will prompt you with the message, ‘Extended Successfully.

  • The blue LED light indicator indicates proper connection, whereas the red LED light indicator indicates the possibility of a better connection.

  • Move it closer to ensure the connection is proper and the blue LED light is lit.


  1. Rockspace extender setup using the WPS button - 

  • Just wait for the power light to turn solid because that indicates your wifi extender is turned on. 

  • Then, hit the WPS push button on your rockspace wifi extender.

  • Within the next two minutes, hit the WPS push button on the wifi router as well. 

  • If the light indicator on the extender is solid then, it implies the connection is proper.

  • Reset the wifi extender in case it doesn’t get started.

  • To make the WPS settings, you can also, do the following;

  • Navigate to the router’s web page.

  • Then look for the settings and click on that. 

  • Choose the WPS option, and enable it.

  • Finally, just detach the plug and attach it within the range of the wifi router.


Steps For Rockspace Wifi Extender Configuration -

If you want to configure the Rockspace wifi extender then you need to configure http://re.rockspace.local. Follow the steps to learn how to do so;

  • First of all, link your PC device or mobile phone to the Rockspace extender’s network.

  • Open up any web browser.

  • In the given address bar type, re.rockspace.local and then press enter.

  • In case, the site doesn’t open, type 192.168.0.254 in the address field.

  • Now, you will redirect to the extender’s login page.

  • Enter the login credentials you have set up earlier.

  • After that, you will be taken to the admin panel.

  • Here, you can configure the Rockspace extender easily.

Rockspace Ready To Extend!

Wasn’t that helpful? This guide is an all-in-one solution to all Rockspace extender setup and installation-related queries. So, follow the instructions closely. 192.168.0.254 is a substitute for re.rockspace.local setup so whenever you face an issue with it, log in via the above-mentioned IP address. 
Labels:

Comments

Post a Comment

Popular posts from this blog

How to Do Orbi WiFi Extender Setup?

  With the advancement in technology, the need for the high-speed internet is also growing. Now, the users can’t bear any delayed network issues. We have seen that people will switch easily to other networks until they find an efficient wireless network. Getting reliable wireless signals becomes the challenge. A single router can provide a decent WiFi coverage within a certain range but leave certain areas of your home with poor or no WiFi coverage. If you are facing the slow WiFi signals issue then go ahead with the Orbi WiFi extender that not only boosts the WiFi signals but also eliminates the dead spots. In this blog, all you are going to know about the steps for O rbi wifi extender setup . So, without wasting any of your precious time, let us begin with the most important section of the blog.  Instructions for the Netgear Orbi WiFi Extender Setup Look at the below instructions one-by-one for the Netgear Orbi WiFi extender setup: Step 1: The first step is to unplug the exi...
Post a Comment
Read more

How Do I Setup the Nextbox WiFi Extender?

  In comparison to others, the  Nextbox wifi extender setup  is far too simple. The steps below will help you install it, access its login admin page, and configure its settings. So, without further doubt, let's begin the Nextbox extender setup process.   Nextbox Extender Installation Steps- The following are the steps for installing the Nextbox wifi extender in your home. Essentially, it will assist your router in reaching its signal range in every corner of your home. So, let's get this party started. To begin, you must unbox it. Find a suitable network signal location. Keep it there and connect it to the power source and the router network. Remove the power cable from its packaging box and inspect it for damage; otherwise, it may cause problems. So, make sure its cable and power socket are compatible and connect this power cable to both your power socket and your range extender. Wait until the signal LED stops blinking. When it starts blinking, make sure your exte...
Post a Comment
Read more

How to setup Netgear Nighthawk ac1900 modem router?

  The simplest answer to how to setup Netgear nighthawk ac1900 modem router is through the Nighthawk app. The Nighthawk app also allows you to manage your WiFi settings, view the devices connected to your network, and perform speed tests. Check Which products support the Netgear Nighthawk app to see if your product is supported. You can also configure your router using the web interface if you'd prefer to install it on a computer or if your product isn't supported. For more details, see How do I configure my NETGEAR router using the router web interface.   Utilizing the NETGEAR Nighthawk app, configure and install your NETGEAR router as follows: Get the Nighthawk application. Connect your modem to the router's Internet port after attaching any provided antennas. Start up your router. Await the WiFi LED to turn on. For your router's WiFi network name (SSID) and network key (password), check the label on the device. Your router's label can be found on the bottom or b...
Post a Comment
Read more